Window Treatment Installation in Chicago

Ceiling tracks, curtain rods, and shades, hung level and finished to last.

Trusted ByHomeowners, renters, designers, businesses
Handled PersonallyOwner-installed
Fully InsuredCOI available
What I Install

Ceiling tracks, curtain rods, motorized systems, and shades.

From a single roller shade to every window in a house. Every track, rod, and shade is planned around the actual surface, span, and bracket layout before drilling, so it hangs level and stays supported.

Request Installation

Ceiling tracks

Ceiling-mounted curtain tracks for floor-to-ceiling drapery, long spans, and wide windows, with brackets spaced so nothing sags.

Curtain rods

Single and double rods set at the right height and width for the window, wall-mounted into the right anchors or framing.

Motorized tracks & shades

Mounting, pairing, and calibration for motorized tracks and shades, including replacements for existing electronic blinds.

Shades & blinds

Roller shades and blinds, inside or outside mount, including skylight shades and tall windows, from one window to a whole house.

Curtains & drapery

Hanging and adjusting panels on rods or tracks, including hooks, pins, and pleats, for oversized windows too.

Concrete installation

High-rise concrete ceilings and walls drilled with masonry bits and concrete-rated anchors, plus steel window frames, brick, and plaster.

Common Questions

Window Treatments FAQ

Tracks, motorized systems, tall windows, wall type, and clean placement.

Request Installation

I install curtain rods, curtain tracks, ceiling-mounted tracks, blinds, shades, motorized systems, drapery hardware, and similar window treatment systems.

Yes. Tracks and motorized shades need cleaner alignment and stronger planning than basic rods. I check the mounting surface, bracket layout, power or control requirements, and whether the system has enough support across the full span.

Yes. Ceiling-mounted tracks and treatments are possible when the ceiling condition and hardware allow it. I check the surface first and use proper anchors or structural support instead of relying on weak fasteners.

Yes. Different surfaces need different drill bits, anchors, and techniques. Plaster, masonry, concrete, tile, and drywall are not treated the same because the wrong hardware can loosen over time.

I plan the height, reveal, projection, centerline, bracket spacing, and relationship to the window, ceiling, trim, and floor before drilling. The goal is a clean finished look, not just hardware attached to the wall.

Yes. Tall windows, high ceilings, and large spans may require ladders, extra setup, stronger hardware, or an additional installer. Access and safety are considered before the job is scheduled.

Yes. I can help confirm whether the treatment should sit inside or outside the window opening, how high it should be, how far it should extend, and whether wall or ceiling mounting will look better.

Yes. I can install client- or designer-supplied rods, tracks, brackets, shades, and hardware. If something is missing or not strong enough for the wall, I will point that out before installing it.

I do not rely on weak box hardware when the treatment needs better support. If I decide supplied hardware is not strong or high-quality enough for the system, I replace it with professional-grade hardware selected for the load and surface.

Yes, when the support is right. Heavy fabric, long tracks, wide windows, and multi-panel systems need careful bracket spacing and secure mounting so the system does not sag, flex, or pull loose.

Installation and mounting can be handled as part of the project. Any new electrical wiring or hardwired power work is usually done in tandem with a licensed electrician when needed.

Blinds and shades start at $80 each, curtain rods from $125, curtain tracks from $150, and curtain hanging from $20 per panel. Motorized systems, ceiling installs, and specialty surfaces are quoted per project. The minimum for a scheduled visit is $125. Text photos and window sizes for a quote.

Yes. Steel and metal frames need metal-rated drill bits and fasteners, and careful placement so the brackets sit flat and the blinds hang level. I have installed blinds over solid steel window frames.

Yes. Concrete ceilings and walls need masonry bits and anchors rated for concrete. I have installed large roller shades into concrete ceilings in high-rise windows.

Yes, when the skylight frame and access allow it. I check the frame, the shade hardware, and the ladder setup before the visit.

Yes. Designers and businesses hire me for repeat window treatment installs, and I can work with designer-supplied hardware. Preferred pricing is available for interior designers and art galleries.

Send photos of the windows and hardware, number of windows, treatment type, approximate length and height, wall or ceiling type if known, ZIP code or neighborhood, and preferred day or time.

Yes. I provide a one-year workmanship warranty on all installations. It covers my installation and the hardware I provide. It does not cover the installed item itself, factory hanging hardware unless I replace it, manufacturing defects, accidental damage, misuse, or abnormal wall conditions. If an issue is related to my installation, I will take care of it. My goal is always to install everything to last for many years—ideally for the lifespan of the wall under normal use.